Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
Just about everyone is bound to have their personal assumption with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move easily; if you need to open a wall to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub and set in the brand-new one. See to it you have actually qualified yourself for the task as well as fit trying it. Instead of working with a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water system pipelines.
Your tools as well as material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite problematic because of the limited gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The previous kind ought to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing the two wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the suitable supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water supply and examine all joints and also new pipework for leaks and tighten them if essential. Load the tub and additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last placement.
Planning for the Installation
To start with, the supporting structure provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with moisture and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the activity experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our section about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking the time to read our short article. Do you know another individual who is in the market for the topic? Please feel free to share it. I thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Source
Report this page